HYDRAULIC AUGER FOR KUBOTA RX502VA

Customized on your machine model!

REDUCED: hydraulic auger for kubota rx502va with cast iron gearbox and tapered roller bearings for a higher axial load.
POWERFUL: high torque for stony grounds drilling.
BENDING: hydraulic auger for kubota rx502va with double joint for vertical drilling also on slopes (blocking cylinders are included).
ALL IN ONE: hydraulic auger for kubota rx502va or screw log splitter? You can choose according to your needs.

FIXED: it allows you to make horizontal and diagonal holes.

DIRECT: direct transmission with tapered roller bearings for high axial load.
FAST: high displacement orbital motor for a very good force/speed ratio.
CHEAP: suitable for sandy grounds with low presence of stones.

FIXED: it allows you to make horizontal and diagonal holes.
DIRECT: direct transmission with tapered roller bearings for high axial load.
FAST: high displacement orbital motor for a very good force/speed ratio.
CHEAP: suitable for sandy grounds with low presence of stones.

DRILL BIT AS GIFT: A drill bit is included. You can choose from 80mm to 200mm diameter.
LARGE RANGE: We can supply drill augers to 350mm diameter!
SCALABLE: Linkable rods allow you to increase the drilling depth.
TAPERED SCREW: Convert your auger into a log splitter!

FILL THE FORM BELOW (or use our contacts on the page bottom):

Your name:* Your email address:* Your phone number: Your message:* Privacy Policy (art.13 Legislative Decree no. 196/2003):

We wish to inform you that Legislative Decree. n. 196 of 30 June 2003 ("Law regarding the protection of personal data")
provides for the protection of persons and other subjects regarding the processing of personal data. According to the law, 
this treatment will be based on principles of correctness, lawfulness and transparency and the protection of your privacy 
and your rights.
Pursuant to Article 13 of the law. n.196/2003, we provide the following information: 
1. The information you provide will be used for the following purposes: dissemination of study materials of the cultural 
association Centro Studi e Ricerche Ashlag. The data will be sending in a manner both automatic and manual to the email 
address provided by you 3. The conferment of data is necessary for the proper functioning of the system and any refusal 
to supply such data may lead to failure of the relationship. 4. The data will not be disclosed to other parties, nor will it
be circulated. 5. The data controller is Marconi Hydraulics Srls with email marconioleodinamica@gmail.com. At any time you 
may exercise your rights under Article 7 of D.lgs.196/2003 and in particular:

- Oppose the sending of advertising material or for carrying out market research or commercial communication;

- Oppose for legitimate reasons to the processing of data, within the limits established by law;

- Obtain the cancellation, transformation into anonymous form or block of the same

- Obtain the updating, rectification or integration of data

- Be informed of the identity of the owner and any responsible, the purposes and methods of treatment, the subjects or categories of - persons to whom the personal data may be disclosed;

- Know the existence or not of personal data concerning him and to obtain their communication in an intelligible form;

I AGREE WITH THE TREATMENT OF MY PERSONAL DATA ACCORDING TO THE INFORMATION ABOVE*

FAQ:

Does your machine fit with my excavator?
Our hydraulic augers are customized on customer machine model, so the motor/gearbox couple meets your machine specs.
How much is your machine's force? What happen if it blocks?
The tangential force given by our reduced auger with a 200 mm drill is over half a ton! Your machine's hydraulic plant protects the hydraulic motor against blocks.
Where is it built?
the gearbox, structure and drill bits are all made in Italy!
Is it solid?
It is made up of steel sheets having a 12mm thickness, while the spirals are conceived right for drilling.
The delivery time?!
The delivery time goes from 5 to 7 working days.